Marine Engines
Parts Request Form
BMW Marine Engines
Buick Marine Engines
Crusader Marine Engines
GM Marine Engines
MerCruiser Marine Engines
OMC Cobra
Volvo Marine Engines
Yamaha Marine Engines
|
| |
 |
|
|
Related Topics On MerCruiser Shifting
- MasterGuard Hub Kits
...your drive system from shift shock and impact shock...
- How to get lower unit/gear box back on??
...and rotate the brass shifter (intermediate shift shaft) clockwise looking... ...) The travel of the shifter should be from 10:00... ...Roughly speaking, the shifting should be center of... .... 9) The shift box in the boat should... ...) As you rotate the shifter clockwise, turn the...
- Tilt & Trim ?
...locks when the reverse shifter is engaged, I guess... ...unlock when in forward shift. When in real... ...locks when reverse shift, what would and when...
- Help Capt Ken, another yammie leg question
...discussion that your shifter froze up and would be curious if the shifter in the outdrive froze...
- Trim not locking...outdrive raises in reverse
...noticed that when I shift into reverse to back...
- How hard is it to switch to a dual prop? ('89 King Cobra))
...sliding clutch dog shifting done in the lower )... ...sliding clutch dog shifting )Then they came out... ...and lower)with cone shifting done in the upper .... ...sliding clutch dog shifting in a Bayliner? and...
- Lower unit installation.
...recently replaced the shift cable to the outdrive... ...unit, it will only shift into forward and neutral...
- Water in lower while hoooked to a hose
...impeller? Also the shift shaft seal? How about...
- Alpha One reverse
...started having trouble shifting into reverse. Actually...
- Merc. outdrive kills motor when shifted into forward??
...one new quirk: boat shifts into drive at idle... ...idle) I have checked shift and throttle cable... ...seems fine. adjusting shift cable to either extreme...
- Loss of power
...had new throttle and shift cables installed, then...
- Whine from lower unit
...whine at full speed. Shifting and throttle all smooth...
- Oil seeping from sterndrive
...your description the shift shaft seal was likely...
- Grease the gimbal bearing
...and rotate the brass shifter (intermediate shift shaft) clockwise looking... ...) The travel of the shifter should be from 10:00... ...Roughly speaking, the shifting should be center of... .... 9) The shift box in the boat should... ...) As you rotate the shifter clockwise, turn the...
- HELP lining up gear linkage
..., the prop and gear shift are all messed up.... ...every time I tried to shift to forward or reverse...
- OMC cobr***
...and look up at the shift cable. It should be... ...for 100% operation. Shifts EZily and accelerates... ...correctly. Changing a shift cable on a Cobra is...
- Drive shaft bellow removal help
...REPLACEMENT OF THE U-JOINT, SHIFT CABLE, AND EXHAUST... ...tip from the lower shift cable. Remove the... ...) Push the shift cable back into boat...
- Outdrive won't go on........help
...away from fishin' I've shifted gears, turned prop,...
- OMC Stern Drives- Dinosaurs or OK?
...in my Starcraft. It shifts much smoother than... ...runs really well. It shifts "smooth as silk" and... ...sterndrive and it doesn't shift nearly as smoothly....
- Bravo noise
...drive that needs the shift cables adjusted. I have checked the shift cables and they are...
- Shift lever problem
...with my throttle / shifter. It is I/O 14... ...’s the type of shifter that you could pull... ...in neutral. While shifter is “pushed in... ...forward or reverse, both shift cable... ...move fine. When the shifter is “pulled out... ...doesn’t and the shifter just drops down freely...
- 3.0 Cobra knocking noise
...advanced. Also, the shift cam which actuates... ...up and allowed it to shift easier and more positively...
- 4 cyl or V6 sterndrive?
...old OMC Cobra drive shifts much easier than the...
- 260 Mercrusier micro switch on linkage for shifting????
...the linkage to the shift and throttle bracket...
|
|
|
